Dental handpiece repair software for mail-in repair shops
For shops that repair dental handpieces and equipment: one ticket per handpiece with its serial number, batches from a practice booked in by copying, mail-in parcels both ways, rush jobs, practice accounts with balances, repair warranty and repeat repairs.

ServiceCenterSoft is job-tracking software for shops that repair dental handpieces and equipment. High-speed turbines, low-speed contra-angles and straight handpieces, cartridges and bearings, electric and air motors, scaler handpieces, plus on-site work on dental units and compressors. Every handpiece gets its own ticket with a serial number, a promised date, an itemised estimate and a history. It runs in the browser, on the bench PC and on a phone.
This page is for a narrow trade: nearly every customer is a practice, and the items are small and look alike. If you service clinical equipment more broadly, see medical equipment repair software; for another small, high-value repair trade, see hearing aid repair software.
Who it is for, and what goes wrong
A dentist without a handpiece cannot treat patients, so every repair is urgent. And handpieces rarely arrive one at a time: a practice saves them up and posts a box of five to ten, often several of the same model.
The familiar trouble spots:
- the box is logged as “8 handpieces” and a week later nobody can say which one already has a new turbine;
- a handpiece comes back noisy after two months and there is no record of what was replaced last time;
- the return tracking number lives in one person’s phone;
- a loaner went out “for a week” and nobody remembers which practice has it;
- the practice pays monthly in one lump, and what they owe is worked out from a notebook every time;
- a handpiece arrives without having been reprocessed, and your intake terms are not written anywhere.
One ticket per handpiece, batches by copying
A ticket in the software covers one item. You cannot book a whole box on a single ticket — and for handpieces that is right, because each has its own serial number, fault and repair price. Instead, tickets are copied. Fill in the first one fully: the practice, the item type from your own list (“High-speed handpiece”, “Contra-angle”, “Motor”, “Scaler”), the model, the fault. The rest are copies — customer, type, fault and notes carry over, while the serial number deliberately does not: you enter it for each handpiece. A “copy last ticket” button does it in one click.
Search finds a ticket by part of a serial number. Type the digits engraved on the body and you see every earlier repair of that handpiece: when it was in, which jobs and parts were on the estimate, what it cost. The repair receipt page shows what the printed document looks like.

The practice as the customer: payments and balance
The customer record has a company field, and the practice name prints on the ticket and the completion certificate next to the contact’s name. Searching the job list by that name brings up every handpiece from the practice. The customer record shows all their repairs, the total and the balance still unpaid.
A ticket can take several payments and shows “received” and “balance due”; the “unpaid” filter lists jobs that went back without being paid for. The software does not issue invoices: it prints the intake ticket and the completion certificate, with the estimate as a table, the work log and your recommendations.
Mail-in repair: parcels in and out
Most handpiece repair is mail-in. You define the statuses yourself — “In transit to us”, “Received from parcel”, “Shipped back” — and type the tracking number as plain text in the comment on the status change. It stays in the ticket history with the date and name. Any status can sit as a tile above the list, so one click shows everything in transit.
There is no carrier integration: the software does not create shipping labels or track parcels; the number is stored as text only.

Reprocessed before shipping: your intake terms on the ticket
A handpiece has been in a patient’s mouth, and a repair shop is entitled to expect it cleaned and sterilised before it is sent. You write that condition yourself into the wording of your ticket under “Print forms” — for example, that items are accepted only if reprocessed according to the rules in your country and the manufacturer’s instructions. It then appears on every ticket. If something arrives otherwise, note it in the “Condition” field of that ticket.
The software checks none of this and keeps no sterilisation logs. How an item must be reprocessed before shipping and after repair is set by local rules and the manufacturer, not by us.
Standard jobs and estimates
Handpiece repairs repeat: turbine or cartridge replacement, bearing replacement, chuck, O-rings, clean and lubricate, contra-angle gear overhaul, motor repair. These sit in your price list of standard jobs — pick a line and the amount is on the ticket. Parts are added as lines from stock.
When a strip-down shows the repair will cost more than expected, the estimate goes to the practice by email or Telegram. The link shows every line with “I agree” and “I decline” buttons, and the answer lands in the history with its date. Approved by phone instead? Record it as a comment on the status change.
Rush jobs and loaner handpieces
Every ticket has a promised date. Overdue jobs turn red and gather under the “overdue” filter, and an urgent flag makes a ticket stand out in the list. A model-specific part is requested from the ticket and emailed to your supplier; meanwhile the job sits in a “waiting for parts” status.
There is no separate loaner module. Shops keep track like this: on the ticket for the handpiece under repair, write “loaner issued, serial no. …” in a field that prints on the document, so the practice has it on paper. Add your own status, “Loaner with customer”, and put it above the list as a tile — it shows every ticket where your handpiece has not come back yet.
Repair warranty and repeat repairs
You state your warranty period in the wording of the completion certificate, which you edit yourself. When a handpiece returns with the same complaint, a serial-number search brings up the previous ticket: the date it went back and the estimate lines tell you whether it is still under warranty and what was replaced. The new ticket gets the repair type “Repeat repair”. The job list can be filtered by repair type, which is how you review all repeats. Reports are not broken down by repair type.
Stock: turbines, bearings, chucks
Stock is a movement journal: receipts with cost price and supplier, items used on a job as estimate lines, returns, stocktakes. Turbines and cartridges by model, bearings, chucks, O-rings, bulbs and light guides, scaler tips. Each item has a minimum level, and the “running low” tile tells you when to reorder. Quantities are whole numbers — count by the piece.

Chairs and units: on-site repair
A dental unit or compressor is repaired where it stands. An on-site call is an ordinary ticket: the practice, the type “Dental unit”, serial number, fault, promised date. Labour and parts go on as estimate lines, the completion certificate is printed afterwards, and you can open the ticket on your phone in the surgery. There is no visit calendar or route planning.
Ready notices
When a job is finished, the customer gets an email or a Telegram message, and finished tickets show how many days they have been waiting. Setup is described on the customer notifications page. The software does not send SMS.
What handpiece repairs typically cost
A rough guide only — prices vary by country, model and parts: evaluation €0–25, clean and lubricate €20–50, bearing replacement on a high-speed handpiece €60–150, turbine or cartridge replacement €90–250, contra-angle overhaul €120–350, motor repair €100–300, scaler handpiece €50–180. You set your own prices in the price list of jobs and in the estimate lines.
What it does not have
- one ticket for several handpieces, or a batch document;
- a loaner pool module — only a note on the ticket and your own status;
- parcel tracking or carrier integrations;
- sterilisation logs or any check of reprocessing;
- a visit calendar, or invoices;
- photos or attachments on a ticket, SMS, a mobile app, online payment by the customer.
What it costs
One price for the whole shop — no extra charge for staff or branches.
Monthly
Paid every month, cancel whenever you like.
Yearly
Cheaper than paying monthly. Invoice or card payment.
Custom work
Changes tailored to the way you work — hourly, by agreement.
Off-the-shelf not enough — your own forms, roles, reports or workflow? We will build a program for you. How it works
Try it without signing up in the demo: add a “High-speed handpiece” type, book one in with a serial number, copy the ticket for a second one and add a bearing replacement from the price list.

We are very happy working with servicecentersoft.com: they built everything we asked for, even though our request was unusual, since we deal with medical devices. Everything was done precisely and on the agreed schedule. Thank you for the cooperation — we keep working together.

I tried the ServiceCenterSoft demo and came away with a good impression. The program is simple and easy to understand, yet it has everything you need for the job: customers, repairs, devices, spare parts, statuses and statistics.
I especially liked the dark theme and the responsive design — working from a phone is perfectly comfortable. Another plus is the instant search that works as you type, so you don't have to press a separate "Search" button every time.
You can tell the program was built specifically for service centers rather than being a generic CRM adapted for the repair business. The interface has no unnecessary frills; everything is logical and to the point.
A good, practical tool for the day-to-day work of a service center.

I liked that you get a free 14-day trial and that they are willing to handle my special requests — setting things up exactly the way I need them.
I also liked how payment works. You can simply pay the monthly fee by card online — basically the same as a regular Spotify subscription or any other service. No separate contracts to sign and no invoices to pay manually.
And there's no feeling of strict limits on the number of employees. One service center is one account, and inside it you can organize the work of your technicians and run several branches.
For me this is far more convenient than plans where you have to pay for every single user or keep counting how many employees are working today.

My business is fairly specific, so the program's standard features weren't enough — I needed my own custom fields, my own sorting options and search by additional parameters. The work completion certificate and the printed repair receipt also needed some changes to fit the way we work.
I contacted technical support. To be honest, I expected changes like these to take a long time, but everything was done within a single day. The team quickly understood exactly what we needed, suggested the right solution and did everything properly.
I'd especially like to mention the support: they get straight to the point, with no unnecessary bureaucracy, and they genuinely help instead of just sending you off to read the documentation.
For me this is a big advantage of the program: it isn't just sold "as is" — it can be adapted to how you actually work. Thanks to the team for the quick response and for treating the customer right.
Highly recommended!
In short
- One handpiece, one ticket with its serial number; a batch is booked in by copying.
- The practice is one customer with a company name, several payments and a balance.
- Mail-in parcels: your own statuses, tracking number as text in the history.
- “Reprocessed before shipping” — your wording on your own ticket form.
- Standard jobs from the price list; costly repairs get estimate approval by link.
- Warranty returns: the “Repeat repair” type and history by serial number.
- Loaners as a note on the ticket; there is no separate module.
- €20 a month for the whole shop.
See also
Air compressor repair software for compressor and air tool service shops
For compressor service companies and pneumatic tool repair shops: air tools across the bench, rotary screw machines serviced on site, hours-based maintenance with filters and oil from stock, estimate approval before an airend is opened, and a history for every machine by serial number.
Read moreStarting your own repair shop: where to begin
For people who can fix phones and laptops and want to work for themselves: what a small repair business needs on day one, the paperwork that protects you from the first customer, and how to run a shop in a country whose language is not your own.
Read moreSoftware for home appliance service
Contents recorded at intake, warranty at the brand price list, callouts, slow parts and partner shops.
Read moreSee how it works
The demo is open — go in and try it. Ask us anything by email, Telegram or the form on this site.